Features Trades AI Software Guide AI Agents Done for you Pricing Blog About FAQ Sign in Get access
LV-101

Low voltage software for camera, alarm and access control jobs.

Cameras, alarms, access control and data cabling, plus the cameras-offline call on a Monday morning. Built for small low voltage shops with a few installers.

Service callSample
Two cameras offline
Renee Okafor · 530 Juniper Ave · Tech: Andre
  1. Booked
  2. On site
  3. Done & paid
  • Replace bad cable run$345
  • + Replace failed camera$420
  • New 8-camera recorder$1,150
Signed on the phone
Paid on site$765
LV-102Booked · On site · Done & paid

From the phone call to the payment, in four steps

Every call has three states your whole team can see: Booked, On site, Done and paid. Nothing sits in a text thread.

  1. Book

    Take the call, pick the address, the tech and the time. The cameras-offline call lands on the right tech's day.

  2. On the way

    One tap texts the customer that the tech is on the way. No more "where are you?" calls to the office.

  3. On site

    The tech picks the price from your price book, adds options, takes photos and writes what was found and done. Two offline cameras can go out as three choices: a new cable run, the run plus a new camera, or a new recorder as well. The customer signs on the phone.

  4. Done & paid

    Card or bank on the spot, or a pay link by text. The customer gets a service report, and a few minutes later a request for a review.

The owner sees the whole day by tech. Each tech sees only their own day. Text messages need a one-time number registration, which we set up with you.

LV-103Projects

Camera, alarm and access jobs, step by step

Once the drywall is up, a missed cable is an access hole and a patch nobody priced. Opsite gives every system its own six steps, so rough-in is checked before the walls close and nothing is handed over untested.

  1. Site Survey
  2. Design
  3. Cable Rough-In
  4. Devices
  5. Program & Test
  6. Handover
  • ✓ Site Survey: device locations marked, cable paths, power and network checked, existing equipment photographed
  • ✓ Design: device layout and count approved by the client, permit tracked where the city requires one
  • ✓ Cable Rough-In: a checklist before the step starts, and photos before the walls close
  • ✓ Devices: cameras, sensors, readers and locks mounted, serial numbers photographed
  • ✓ Inspections tracked: Rough-In Before Walls Close, Cable Test & Labeling, Door Release & Egress Test, Alarm Signal Test, Final / Alarm Permit
  • ✓ Program & Test: every device tested and named, test result photos filed on the job
  • ✓ Handover: a checklist for client training, changed default passwords, logins and the as-built drawing
LV-104Low Voltage & Security

What changes for low voltage and security contractors

Six things owners tell us they wanted and could not get from paper, texts and three different apps.

Rough-in checked before the drywall

The Rough-In Before Walls Close checklist covers cable support, firestop, service loops and a box at every device. Photos are filed under Cable Rough-In and Firestop & Penetrations.

The site remembers what is installed

The recorder, the panel, the camera count and where the head end is stay on the address with past visits. A tech who has never been there does not start from zero.

Add-a-camera priced on site

The tech picks from your price book and offers up to three choices. The customer signs on the phone and can pay by card before the ladder is back on the van.

A blocked wall becomes a signed change

When there is no cable path, write the change order on the job: move the device, run exposed raceway, or open the wall. The client signs before anyone cuts an access hole.

Paid at rough-in, devices and test

Progress payments are tied to the job's steps. The money does not all wait on a training session the client keeps moving.

A test record for every door and zone

Door Release & Egress Test and Alarm Signal Test are checklists on the job, with test result photos. If a door is ever questioned, you can show it was tested at handover.

LV-105Before and after

Your day today, and your day on Opsite

The same seven moments of a normal week, side by side.

WhatHow most small shops run itWith Opsite
Cameras offlineA text to whoever is closestBooked on a tech's day with the site's notes
What is on siteWhoever installed it remembersEquipment, notes and past visits on the address
Before the walls closeA quick look and hopeRough-In Before Walls Close checklist with photos
A wall with no pathExtra labor nobody approvedA change order the client signs first
Door release testTested, but never written downDoor Release & Egress Test checklist on the job
Final paymentHeld until the client finds time for trainingProgress payments tied to each step, through Handover
Backup batteriesChanged after the panel starts beepingA yearly reminder to offer the battery change
LV-106

Questions low voltage and security contractors ask us

Is Opsite only for big security companies?

No. It is built for small low voltage shops: an owner who still walks the site surveys, an office person and a few installers. Start with service calls or with installs, whichever is the bigger mess today.

Does Opsite connect to cameras, panels or a monitoring station?

No. Opsite does not monitor alarms and does not connect to devices. It runs the work around them: the call, the proposal, the steps, the tests, the photos and the payment.

Can it handle a one-camera add and a 24-drop cabling job?

Yes. A small add or a troubleshooting visit is a service call: Booked, On site, Done and paid. A full system is a job with six steps, from Site Survey to Handover.

How do I keep track of permits?

Permits are tracked on the job, and the Final / Alarm Permit checklist asks for the owner's city alarm permit number. Opsite does not file a permit for you.

Who pays for patching the access holes?

Your standard terms go on every proposal, so if drywall patching and paint are not included, the client signs that before the job starts. A hole nobody planned goes on a change order.

How much does it cost?

Book a demo. We will show it on one of your own jobs and go over the plan that fits your company.

LV-107We contact you

See it on one of your own calls

Bring a real call from last week. We will book it, price it and close it in front of you.

  1. Leave your details. It takes a minute.
  2. We look at your company and contact you. A person calls or texts you.
  3. We show Opsite on your own calls. Then you decide.

We open access one company at a time. You do not need a card or a contract to ask.

LV-108

What is Opsite for low voltage and security contractors?

Opsite is software for contractors and service companies. For low voltage and security contractors it runs service calls from booked to paid, with a price book, options the customer signs on the phone, payment on the spot, a service report and a review request. Bigger jobs run as projects with their own steps, permits and inspections. Proposals, invoices, purchase orders, a time clock and a client portal are part of the same account.