Features Trades AI Software Guide AI Agents Done for you Pricing Blog About FAQ Sign in Get access
G-101

Gate software for repair calls and custom gates built in your shop.

Custom driveway and walk gates, operators, access control, fences and railings, plus the repair calls. Built for small gate and iron companies with a shop and a few trucks.

Service callSample
Driveway gate stuck open
Owen Castellan · 77 Ridgecrest Ct · Tech: Luis
  1. Booked
  2. On site
  3. Done & paid
  • Replace control board$685
  • + New photo eyes$240
  • New slide gate operator$3,400
Signed on the phone
Paid on site$925
G-102Booked · On site · Done & paid

From the phone call to the payment, in four steps

Every call has three states your whole team can see: Booked, On site, Done and paid. Nothing sits in a text thread.

  1. Book

    Take the call, pick the address, the tech and the time. The call about a driveway gate stuck open lands on the right tech's day.

  2. On the way

    One tap texts the customer that the tech is on the way. No more "where are you?" calls to the office.

  3. On site

    The tech picks the price from your price book, adds options, takes photos and writes what was found and done. A dead operator can go out as three choices: a new control board, the board with new photo eyes, or a new operator. The customer signs on the phone.

  4. Done & paid

    Card or bank on the spot, or a pay link by text. The customer gets a service report, and a few minutes later a request for a review.

The owner sees the whole day by tech. Each tech sees only their own day. Text messages need a one-time number registration, which we set up with you.

G-103Projects

Custom gates, fences and railings, step by step

A custom gate spends weeks in the shop while the approvals and the 811 ticket run on their own clocks. Opsite gives it seven steps, so no steel is cut before the drawing is signed and no hole is dug before the ticket is clear.

  1. Design & Measure
  2. Approvals & 811
  3. Fabrication
  4. Site Prep
  5. Install
  6. Automation & Test
  7. Closeout
  • ✓ Design & Measure: opening width, slope, swing or slide, run-back room and distance to power on the job
  • ✓ Approvals & 811: HOA and city approvals in hand, the dig ticket number saved on the job
  • ✓ Fabrication: a checklist first: shop drawing signed, finish color picked, deposit received
  • ✓ Site Prep and Install: footings, trench and conduit photographed before they are covered, columns cured before the gate hangs
  • ✓ Inspections tracked: 811 Dig Ticket, Footing / Pier, Underground Electrical, Shop QC, Final Electrical, Gate Safety Check, Final Building
  • ✓ Automation & Test: photo eyes, safety edges and the obstruction test checked off with photos
  • ✓ Closeout: warning signs up on both sides, manual release shown to the client, punch list closed, final invoice
G-104Gates & Iron

What changes for gate and iron companies

Six things owners tell us they wanted and could not get from paper, texts and three different apps.

No steel cut on a verbal OK

The proposal is signed online, and the signed shop drawing is on the checklist before Fabrication. A design change after that is a change order the client signs, with a price.

The dig is clear before the crew arrives

The 811 Dig Ticket check has its own checklist: ticket number on the job, marks photographed, two working days passed, ticket still current.

Proof the gate is safe

The Gate Safety Check covers photo eyes, safety edges, the obstruction test, warning signs and the manual release. It stays on the job with photos if anyone ever asks.

Stuck-gate calls paid at the gate

A repair is a service call: Booked, On site, Done and paid. The tech prices it from your price book, the customer signs on the phone and pays by card or bank.

The operator is on record at every address

Notes and equipment are kept per address with past visits. The tech knows the operator, the keypad and what was replaced last time before driving out.

Paid as the gate gets built

Progress payments follow the job: shop drawings approved, fabrication complete, installed, automation tested. You are not carrying weeks of steel and powder coat on a 10 percent deposit.

G-105Before and after

Your day today, and your day on Opsite

The same seven moments of a normal week, side by side.

WhatHow most small shops run itWith Opsite
A gate stuck openWhoever answers the phone texts a techThe call is on the right tech's day, with the address notes
Pricing the repairThe tech guesses a number at the keypadYour price book, with up to three options
Approving the designA sketch, a text and a handshakeSigned proposal, and the signed drawing checked off before Fabrication
Calling 811Someone remembers, usuallyA dig ticket checklist with the ticket number and photos
Weeks in the shopThe client calls to ask where the gate isThe client portal shows the step and the fabrication photos
Safety devicesTested, but nothing written downA Gate Safety Check with photos saved on the job
Getting paid on a custom gateA deposit, then a fight over the balancePayments at drawings, fabrication, install and final test
G-106

Questions gate and iron companies ask us

Is Opsite only for big gate companies?

No. It is built for small gate and iron companies: an owner, a shop, an install crew and a service tech or two. You can start with repair calls only and add custom jobs later.

Can I run repairs and custom gate jobs in the same place?

Yes. A repair is a service call with three states: Booked, On site, Done and paid. A custom gate is a job with seven steps, from Design & Measure to Closeout, with its own checks and payments.

What happens when the client changes the design after we start building?

It becomes a change order with a price, and the client signs it before the shop touches the steel again. Your standard terms already say custom work is built from the approved drawings.

Does it keep track of 811 and the safety testing?

Yes. 811 Dig Ticket and Gate Safety Check are checks on the job, each with its own checklist. The ticket number, the marks and the obstruction test are saved with photos.

How does a customer pay for a repair?

By card or bank at the gate, or with a pay link sent by text. Then they get a service report with what was found, what was done and the photos.

How much does it cost?

Book a demo. We will show it on one of your own jobs and go over the plan that fits your company.

G-107We contact you

See it on one of your own calls

Bring a real call from last week. We will book it, price it and close it in front of you.

  1. Leave your details. It takes a minute.
  2. We look at your company and contact you. A person calls or texts you.
  3. We show Opsite on your own calls. Then you decide.

We open access one company at a time. You do not need a card or a contract to ask.

G-108

What is Opsite for gate and iron companies?

Opsite is software for contractors and service companies. For gate and iron companies it runs service calls from booked to paid, with a price book, options the customer signs on the phone, payment on the spot, a service report and a review request. Bigger jobs run as projects with their own steps, permits and inspections. Proposals, invoices, purchase orders, a time clock and a client portal are part of the same account.